Publications

International Journal Papers

No. Authors Article Info. Year
123

Sim, J. B., Yook, S. J., and Kim, Y. W.

Performance analysis of organic Rankine cycle with the turbine embedded in a generator (TEG), 

Energies, 15:309.
2022
122

Lim, J. H., and Yook, S. J.

Development of a high-volume ambient aerosol sampling inlet with an adjustable cutoff size and its performance evaluation using road dust, 

Environmental Research, 204:112302.
2022
121

Khan, U., Zaib, A., Ishak, A., Bakar, S. A., Animasaun, I. L.,

and Yook, S. J.

Insights into the dynamics of blood conveying gold nanoparticles on a curved surface when suction, thermal radiation, and Lorentz force are significant: The case of Non-Newtonian Williamson fluid, 

Mathematics and Computers in Simulation, 193:250-268.
2022
120

Animasaun, I. L., Yook, S. J., Muhammad, T., and Mathew, A.

Dynamics of ternary-hybrid nanofluid subject to magnetic flux density and heat source or sink on a convectively heated surface, 

Surfaces and Interfaces, 28:101654.
2022
119

Song, G., Moon, E. S. , Park, J. J., Song, S. M., and Yook, S. J.

Performance investigation of radial heat sink with pin fins placed normally on circular base edge, 

International Journal of Thermal Sciences, 171:107187.
2022
118

An, I. H., Lee, C. H., Lim, J. H., Lee, H. Y., and Yook, S. J.

Development of a miniature cyclone separator operating at low Reynolds numbers as a pre-separator for portable black carbon monitors, 

Advanced Powder Technology, 32:4779-4787.
2021
117

Shah, N. A, Wakif, A., Shah, R., Yook, S. J., Salah, B.,

Mahsud, Y., and Hussain, K.

Effects of fractional derivative and heat source/sink on MHD free convection flow of nanofluids in a vertical cylinder: a generalized Fourier’s law model, 

Case Studies in Thermal Engineering, 28:101518.
2021
116

Zahir, M. Z., Lim, J. H., Noh, S. Y., and Yook, S. J.

Development of electric virtual impactor with variable sampling particle size range, 

Advanced Powder Technology, 32:3456−3464.
2021
115

Lim, J. H., Nam, S. H., Kim, J., Kim, N. H., Park, G. S.,

Maeng, J. S., and Yook, S. J.

High-volume sampler for size-selective sampling of bioaerosols including viruses, 

Atmospheric Environment, 265:118720.
2021
114

Lee, J., Park, S. H., Sung, G. B., An, I. H., Lee, K. R., Hong, S. P., Yook, S. J., and Koo, H. B.

Effect of air cleaner on reducing concentration of indoor-generated viruses with or without natural ventilation, 

Aerosol Science and Technology, 55:1288−1303.
2021
113

Noh, S. Y., Lee, K. R., Noh, J. H., Kim, H. S., and Yook, S. J.

Comparison of resuspended road dust concentration for identifying optimum sampling position on a mobile laboratory vehicle, 

Aerosol Science and Technology, 55:1230−1238.
2021
112

Lim, J. H., Oh, S. H., Kang, S., Lee, K. J., and Yook, S. J.

Development of cutoff size adjustable omnidirectional inlet cyclone separator, 

Separation and Purification Technology, 276:119397.
2021
111

Song, G., Kim, D. H., Song, D. H., Sung, J. B., and Yook, S. J.

Heat-dissipation performance of cylindrical heat sink with perforated fins, 

International Journal of Thermal Sciences, 170:107132.
2021
110

Lim, J. H., Hwang, S. J., and Yook, S. J.

Analysis of the aspiration ratio of double-shrouded probes according to angle of attack and probe scale, 

Aerosol Science and Technology, 55:1202−1213.
2021
109

Zafar, A. A., Awrejcewicz, J., Kudra, G., Shah, N. A.,

and Yook, S. J.

Magneto-free-convection flow of a rate type fluid over an inclined plate with heat and mass flux, 

Case Studies in Thermal Engineering, 27:101249.
2021
108

Shah, S. Z. H., Ayub, A., Sabir, Z., Adel, W., Shah, N. A.,

and Yook, S. J.

Insight into the dynamics of time-dependent cross nanofluid on a melting surface subject to cubic autocatalysis, 

Case Studies in Thermal Engineering, 27:101227.
2021
107

Xia, W. F., Animasaun, I. L., Wakif, A., Shah, N. A.,

and Yook, S. J.

Gear-generalized differential quadrature analysis of oscillatory convective Taylor-Couette flows of second-grade fluids subject to Lorentz and Darcy-Forchheimer quadratic drag forces, 

International Communications in Heat and Mass Transfer, 126:105395.
2021
106

Kundu, B., and Yook, S. J.

An accurate approach for thermal analysis of porous longitudinal, spine and radial fins with all nonlinearity effects – analytical and unified assessment, 

Applied Mathematics and Computation, 402:126124.
2021
105

Cho, M. C., Jo, Y. G., Son, J., Kim, I., Oh, C., and Yook, S. J.

Deposition characteristics of soot and tire-wear particles on urban tree leaves, 

Journal of Aerosol Science, 155:105768.
2021
104

Lee, J., Noh, J. H., Noh, K. C., Kim, Y. W., and Yook, S. J.

Effect of a system air conditioner on local air quality in a four-bed ward, 

Aerosol and Air Quality Research, 21:200533.
2021
103

Kim, M. W., Noh, S. Y., Zahir, M. Z., and Yook, S. J.

Performance improvement of a horizontal zigzag type mist eliminator by using slit plates, 

Journal of Mechanical Science and Technology, 35:2229−2236.
2021
102

Noh, S. Y., Ji, J. H., Kim, H. S., and Yook, S. J.

Required flux tower height for measurement of re-suspended road dust, 

Journal of Mechanical Science and Technology, 35:1781−1789.
2021
101

Lee, G. H., Hwang, S. Y., Cheon, T. W., Kim, H. J., Han, B., 

and Yook, S. J.

Optimization of pipe-and-spike discharge electrode shape for improving electrostatic precipitator collection efficiency, 

Powder Technology, 379:241-250.
2021
100

Dutta, J., Kundu, B., and Yook, S. J.

Three-dimensional thermal assessment in cancerous tumors based on local thermal non-equilibrium approach for hyperthermia treatment, 

International Journal of Thermal Sciences, 159:106591.
2021
99

Noh, S. Y., Park, D., and Yook, S. J.

Numerical investigation of bus stop structures in Seoul for the reduction of fine dust entry, 

Journal of Mechanical Science and Technology, 35:371-379.
2021
98

Noh, S. Y., Kim, M. W., and Yook, S. J.

Performance investigation of a vertical wave-plate mist eliminator with perforated plates, 

Aerosol and Air Quality Research, 20:2681-2689.
2020
97

Lim, J. H., Park, S. H., Yook, S. J., and Ahn, K. H.

Aspiration ratio of a double-shrouded probe under low pressure conditions in troposphere, 

Aerosol Science and Technology, 54:1323-1334.
2020
96

Lee, H. D., Yook, S. J., ​and Ahn, K. H.

Effects of exponentially decaying and growing concentrations on particle size distribution from a scanning mobility particle sizer, 

Aerosol Science and Technology, 54:1135-1143.
2020
95

Lim, J. H., Park, D., ​and Yook, S. J.

Development of a multi-slit virtual impactor as a high-volume bio-aerosol sampler, 

Separation and Purification Technology, 250:117275.
2020
94

Noh, S. Y., Zahir, M. Z., Ryoo, B., and Yook, S. J.

Effect of a protective shape upstream a sensor on reducing dust particle contamination of critical sensor surface, 

Sensors and Actuators A, 312:112126.
2020
93

Woo, S. H., Lee, J. I., Kim. J. B., Bae, G. N., Lee, S. B.,

Yook, S. J., and Shin, Y.

Characteristics of dust-collection efficiency and ozone emission by high voltage electrode shape of electrostatic precipitator for subway tunnel environment, 

Journal of Mechanical Science and Technology, 34:1351−1363.
2020
92

Lim, J. H., Park, S. I., Lee, H. J., Zahir, M. Z., and Yook, S. J.

Performance evaluation of a tangential cyclone separator with additional inlets on the cone section, 

Powder Technology, 359:118−125.
2020
91

Zahir, M. Z., Heo, J. E., and Yook, S. J.

Influence of clean air and inlet configuration on the performance of slit nozzle virtual impactor, 

Advanced Powder Technology, 30:3224−3230.
2019
90

Sundar, S., Song, G., Zahir, M. Z., Jayakumar, J. S., 

and Yook, S. J.

Performance investigation of radial heat sink with circular base and perforated staggered fins, 

International Journal of Heat and Mass Transfer, 143:118526.
2019
89

Woo, S. H., Cheon, T. W., Lee, G.,

Kim, J. B., Bae, G. N., Kwon S. B., Jang, H. R., and Yook, S. J.

Performance evaluation of a hybrid dust collector for removing particles during subway train operation, 

Aerosol Science and Technology, 53:562-574.
2019
88 Joe, Y. H., Shim, J., Shin, I. K., Yook, S. J., and Park, H. S. A study on electrical charge distribution of aerosol using Gerdien ion counter,

Aerosol and Air Quality Research, 18:2922-2928.
2018
87 Woo, S.H., Kim, J. B., Bae, G. N., Hwang, M. S., Yoon, H. H., Kwon, S. B., Park, D., and Yook, S. J. Size-dependent characteristics of diurnal particle concentration variation in an underground subway tunnel,

Environmental Monitoring and Assessment, 21:740-753.
2018
86 Noh, J. H., Lee, J., Noh, K. C., Kim, Y. W., and Yook, S. J. Effects of hospital ward curtains on ventilation in a four-bed hospital ward,

Aerosol and Air Quality Research, 18:2643-2653.
2018
85 Woo, S. H., Kim, J. B., Bae, G. N., Hwang, M. S., Tahk, G. H., Yoon, H. H., and Yook, S. J. Investigation of diurnal pattern of generation and resuspension of particles induced by moving subway trains in an underground tunnel,

Aerosol and Air Quality Research, 18:2240-2252.
2018
84 Noh, S. Y., Heo, J. E., Woo, S. H., Kim, S. J., Ock, M. H., Kim, Y. J., and Yook, S. J. Performance improvement of a cyclone separator using multiple subsidiary cyclones,

Powder Technology, 338:145-152.
2018
83 Noh, J. H., Kwak, D. B., and Yook, S. J. Effects of wall thickness and material property on inverse heat conduction analysis of a hollow cylindrical tube,

Inverse Problems in Science and Engineering, 26:1305-1325.
2018
82 Zahir, M. Z., Heo, J. E., and Yook, S. J. Effects of three-partitioned horizontal inlet and clean air on collection efficiency and wall loss of slit virtual impactors,

Aerosol and Air Quality Research, 18:1131-1140.
2018
81 Heo, N. G., Woo, S. H., Lim, J. H., Yook, S. J., and Ahn, K. H. Investigation of a double shrouded probe for particle sampling in high velocity airflows,

Advanced Powder Technology, 29:1085-1091.
2018
80 Heo, J. E., Zahir, M. Z., Park, H., Seo, H., Park, H., and Yook, S. J. Effect of horizontal inlet on slit-nozzle virtual impactor performance,

Journal of Mechanical Science and Technology, 32:2419-2424.
2018
79 Kwak, D.B., Noh. J. H., and Yook, S. J. Natural convection flow around heated disk in cubical enclosure,

Journal of Mechanical Science and Technology, 32:2377-2384.
2018
78 Heo, N. G., Lim, J. H., Lee, J. W., Lee, J. S., Yook, S. J., and
Ahn, K. H.
Development of a sampling probe for representative sampling of PM at freestream velocities in the range
from 0 to 300 km h-1,

Journal of Atmospheric and Oceanic Technology, 35:727-738.
2018
77 Kim, W. G., Kim, C. K., Lee, J. T., Yun, C. W., and Yook, S. J. Characteristics of nanoparticle emission from a light-duty diesel vehicle during test cycles simulating urban rush-hour driving patterns,

Journal of Nanoparticle Research, 20:94.
2018
76 Sim, J. B., Woo, S. H., Yook, S. J., Kim, J. B., Bae, G. N., and
Oh, S. G.
Baffle dust collector for removing particles from a subway tunnel during the passage of a train,

Journal of Mechanical Science and Technology, 32:1415-1421.
2018
75 Woo, S. H., Lee, J., and Yook, S. J. Effect of a trap zone in reducing nanoparticle contamination of wafers and photomasks in parallel airflow,

IEEE Transactions on Semiconductor Manufacturing, 31:87-96.
2018
74 Kwak, D. B., Kwak, H. P., Noh, J. H., and Yook, S. J. Optimization of the radial heat sink with a concentric cylinder and triangular fins installed on a circular base,

Journal of Mechanical Science and Technology, 32:505-512.
2018
73 Sim, J. B., Yeo, U. H., Jung, G. H., Park, S. B., Bae, G. N., and Yook, S. J. Enhancement of louver dust collector efficiency using modified dust container,

Powder Technology, 325:69-77.
2018
72 Noh, J. H., Kwak, D. B., Kim, K. B.,
Cha, K. U., and Yook, S. J.
Inverse heat conduction modeling to predict heat flux in a hollow cylindrical tube having irregular cross-sections,

Applied Thermal Engineering, 128:1310-1321.
2018
71 Cheon, T. W., Lee, J. Y., Bae, J. Y., and
Yook, S. J.
Enhancement of Collection Efficiency of an Inertial Impactor Using an Additional Punched Impaction Plate,

Aerosol and Air Quality Research, 17:2349-2357.
2017
70 Sim, J. B., Woo, S. H., Kim, W. G.,
Yook, S. J.,Kim, J. B., Bae, G. N., and Yoon, H. H.
Performance estimation of a louver dust collector attached to the bottom of a subway train running in a tunnel,

Aerosol and Air Quality Research, 17:1954-1962.
2017
69 Kwak, D. B., Noh, J. H., Lee, K. S., and
Yook, S. J.
Cooling performance of a radial heat sink with triangular fins on a circular base at various installation angles,

International Journal of Thermal Sciences, 120:377-385.
2017
68 Kim, W. G., Yong, S. D., Yook, S. J.,
Ji, J. H.,Kim, K. H., Bae, G. N., Chung, E. K.,
and Kim, J. H.
Comparison of black carbon concentration and particle mass concentration with elemental carbon concentration for multi-walled carbon nanotube emission assessment purpose,

Carbon, 122:228-236.
2017
67 Kim, W. G., Kim, C. K., Lee, J. T., Kim,
J. S., Yun, C. W., and Yook, S. J.
Fine particle emission characteristics of a light-duty diesel vehicle according to vehicle acceleration and road grade,

Transportation Research Part D, 53:428-439.
2017
66 Noh, J. H., Cha, K. U., and Yook, S. J. Three-dimensional inverse heat conduction modeling of a multi-layered hollow cylinderical tube using input estimation algorithm and thermal resistance network,

International Journal of Heat and Mass Transfer, 106:793-803.
2017
65 Woo, S. H., Kwak, K. H., Bae, G. N.,
Kim, K. H., Kim, C. H., Yook, S. J., Jeon, S.,
Kwon, S., Kim, J., and Lee, S. B.
Overestimation of on-road air quality surveying data measured with a mobile laboratory caused by exhaust plumes of a vehicle ahead in dense traffic areas,

Environmental Pollution , 218:1116-1127.
2016
64 Lee, K. R., Kim, W. G., Woo, S. H., Kim, J. B., Bae, G. N.,
Park, H. K., Yoon, H. H., and Yook, S. J.
Investigation of airflow and particle behavior around a subway train running in the underground tunnel,

Aerosol Science and Technology, 50:669-678.
2016
63 Noh, K. C., and Yook,S. J. Evaluation of clean air delivery rates and operating cost effectiveness for room air cleaner and ventilation system in a small lecture room,

Energy and Buildings, 119:111-118.
2016
62 Noh, J. H., Cha, K. U., Ahn, S. T., and
Yook, S. J.
Prediction of time-varying heat flux along a hollow cylindrical tube wall using recursive input estimation algorithm and thermal resistance network method,

International Journal of Heat and Mass Transfer, 97:232-241.
2016
61 Kim, C. W., Lee, K. S., and Yook, S. J. Effect of air-gap fans on cooling of windings in a large-capacity, high-speed induction motor,

Applied Thermal Engineering , 100:658-667.
2016
60 Park, S. J., Jang,D. S., Yook, S. J., and
Lee, K. S.
Optimization of a chimney design for cooling efficiency of a radial heat sink in a LED downlight,

Energy Conversion and Management, 114:180-187.
2016
59 Woo, S. H., Lee, K. S., and Yook, S. J. Local behavior of deposition velocity onto a flat plate in horizontal airflow under the influence of thermophoresis,

Aerosol Science and Technology , 49:920-927.
2015
58 Park, C. W., Song, D. H., and Yook, S. J. Development of a single cyclone separator with three stages for size-selective sampling of particles,

Journal of Aerosol Science, 89:18-25.
2015
57 Lee, M., and Yook, S. J. Investigation of particulate contamination of heated wafers contained in a closed environment

Journal of Aerosol Science 88:148-158.
2015
56 Noh, J. H., Kim, W. G., Cha, K. U., and
Yook, S. J.
Inverse heat transfer analysis of multi-layered tube using thermal resistance network and Kalman filter,

International Journal of Heat and Mass Transfer 89:1016-1023.
2015
55 Park, S. J., Jang, D., Yook, S. J., and
Lee, K. S.
Optimization of a staggered pin-fin for a radial heat sink under free convection,

International Journal of Heat and Mass Transfer 87:184-188.
2015
54 Park, C. W., Kim, G., Yook, S. J., and
Ahn, K. H.
Investigation of collection efficiency of round-nozzle impactors at different pressures and temperatures,

Advanced Powder Technology, 26:868-873.
2015
53 Ji, J. H., Kim, J. B., Lee, G., Noh, J. H.,
Yook, S. J., Cho, S. H., and Bae, G. N.
Workplace exposure to titanium dioxide nanopowder released from a bag filter system,

BioMed Research International, 524283
2015
52 Kim, D., Yook, S. J., and Lee, K. S. Investigation of radiative and convective heat transfer in storage vaults for improving space efficiency,

International Journal of Heat and Mass Transfer, 80:301-308.
2015
51 Kim, W. G., Lee, H., Yook, S. J., and Lee, K. S. Particle deposition velocity onto EUVL masks in vertical airflow,

IEEE Transactions on Semiconductor Manufacturing, 27:417-421.
2014
50 Kim, D., Yook, S. J., Lee, K. S., Yu, S. H., and Bang, K. S. Scaling method for storage vaults based on thermal-hydraulic characteristics,

Nuclear Engineering and Design, 275:242-248.
2014
49 Kim, M. K., Kim, W. G., Lee, K. S., and Yook, S. J. Collection efficiency of round-nozzle impactors with horizontal annular inlet,

Journal of Aerosol Science, 74:63-69
2014
48 Lee, H., and Yook, S. J. Cyclone performance on removing fibrous particles generated from terry-towels and cotton clothes,

Powder Technology, 262:36-41.
2014
47 Ryu, K., Yook, S. J., and Lee, K. S. Optimal design of a corrugated louvered fin,

Applied Thermal Engineering, 68:76-79.
2014
46 Kim, W. G., Lee, H., Myoung, J. H., Han, S. K.,
Yook, S. J., and Ahn, K. H.
Effect of a horizontal inlet on the collection efficiency of a rectangular-slit-nozzle impactor,

Aerosol Science and Technology, 48:649-654.
2014
45 Kang, S., Yook, S. J., and Lee, K. S. Prediction of particle deposition velocity onto an extreme ultraviolet lithography mask in parallel airflow considering electrophoresis,

International Journal of Modern Physics C, 25:1450010.
2014
44 Ryu, K., Yook, S. J., and Lee, K. S. Forced convection across a locally heated square cylinder near a wall,

Numerical Heat Transfer Part A, 65:972-986.
2014
43 Lee. H., Yook, S. J., and Lee, K. S. Deposition of charged particles on a flat plate in parallel flow in the presence of an electric field,

IEEE Transactions on Semiconductor Manufacturing, 27:287-293.
2014
42 Jang, D., Park, S. J., Yook, S. J., and Lee, K. S. The orientation effect for cylindrical heat sinks with application to LED light bulbs,

International Journal of Heat and Mass Transfer, 71:496-502.
2014
41 Kang, S., Yook, S. J., and Lee, K. S. Gaussian diffusion sphere model to predict deposition velocities under the combined effects of electrophoresis and thermophoresis,

Journal of the Korean Physical Society, 64:832-839.
2014
40 Jang, D., Yook, S. J., and Lee, K. S. Optimum design of a radial heat sink with a fin-height profile for high-power LED lighting applications,

Applied Energy, 116:260-268.
2014
39 Lee, H., Jo, D. H., Kim, W. G., Yook, S. J., and Ahn, K. H. Effect of an orifice on collection efficiency and wall loss of a slit virtual impactor,

Aerosol Science and Technology, 48:121-127.
2014
38 Lee, H., and Yook, S. J. Deposition velocity of particles in charge equilibrium onto a flat plate in parallel airflow under the influence of simultaneous electrophoresis and thermophoresis,

Aerosol Science and Technology, 67:166-176.
2014
37 Kim, W. G., Yook, S. J., and Ahn, K. H. Collection efficiency of rectangular slit-nozzle inertial impactors with impaction plates of elliptical concave curvature,

Aerosol Science and Technology, 47:99-105.
2013
36 Kim, S., Lee, S. C., Yook, S. J., Choi, J. U., and Ahn, K. H. LCD brightness decay due to particulate contamination of back light unit,

Journal of The Korean Physical Society, 62:243-249.
2013
35 Woo, S. H., Yook, S. J., and Han, S. Y Gaussian diffusion sphere model to predict deposition velocity onto wafers in laminar parallel airflow considering thermophoresis,

The European Physical Journal Plus, 127:132.
2012
34 Lee, H., Yook, S. J., and Han, S. Y. The effects of simultaneous electrophoresis and thermophoresis on particulate contamination of an inverted EUVL photomask surface in parallel airflow,

The European Physical Journal Plus, 127:122.
2012
33 Lee, H., Yook, S. J., and Han, S. Y. Particle deposition on face-up flat plates in parallel airflow under the combined influences of thermophoresis and electrophoresis,

Journal of The Korean Physical Society, 61:1028-1036.
2012
32 Woo, S. H., Lee, S. C., and Yook, S. J. Statistical Lagrangian particle tracking approach to investigate the effect of thermophoresis on particle deposition onto a face-up flat surface in a parallel airflow,

Journal of Aerosol Science, 44:1-10.
2012
31 Hwang, H. J., Yook, S. J., and Ahn, K H. Experimental investigation of submicron and ultrafine soot particle removal by tree leaves,

Atmospheric Environment, 45:6987-6994.
2011
30 Kim, Y. J., and Yook, S. J. Enhancement of collection efficiency of inertial impactors using elliptical concave impaction plates,

Journal of Aerosol Science, 42:898-908.
2011
29 Lee, S. C., Kim, W. G., and Yook, S. J. Effect of plate thickness on particle deposition velocity onto a face-up flat plate situated parallel to an airflow,

Journal of Applied Physics, 110:063518.
2011
28 Kim, W. K., Lee, S. C., and Yook, S. J. Numerical investigation of thermophoretic effect on particulate contamination of an inverted flat surface in a parallel airflow,

Journal of The Electrochemical Society, 158:H1010-H1016.
2011
27 Lee, S. C., and Yook, S. J. Experimental investigation of particle deposition on face-up surface of wafers and EUVL photomasks exposed to a parallel airflow,

Journal of The Electrochemical Society, 158:H973-H978.
2011
26 Yu, S. H., Lee, K. S., and Yook, S. J. Optimum design of a radial heat sink under natural convection,

International Journal of Heat and Mass Transfer, 54:2499-2505.
2011
25 Kim, M. S., Lee, J., Yook, S. J., and Lee, K. S. Correlations and optimization of a heat exchanger with offset-strip fins,

International Journal of Heat and Mass Transfer, 54:2073-2079.
2011
24 Choi, W. J., and Yook, S. J. Deposition velocity onto an inverted flat surface in a laminar parallel flow,

Aerosol Science and Technology, 44:919-929.
2010
23 Yook, S. J., Asbach, C., and Ahn, K. H. Particle deposition velocity onto a face-up flat surface in a laminar parallel flow considering Brownian diffusion and gravitational settling,

Journal of Aerosol Science, 41:911-920.
2010
22 Yook, S. J., Hwang, H. J., Lee, K. S., and Ahn, K. H. Particle deposition velocity onto a wafer or a photomask in a laminar parallel flow,

Journal of The Electrochemical Society, 157:H692-H698.
2010
21 Yu, S. H., Lee, K. S., and Yook, S. J. Natural convection around a radial heat sink,

International Journal of Heat and Mass Transfer, 53:2935-2938.
2010
20 Yu, S. H., Lee, K. S., and Yook, S. J. Film flow around a fast rotating roller,

International Journal of Heat and Fluid Flow, 30:796-803.
2009
19 Fissan, H., Asbach, C., Kuhlbusch, T. A. J., Wang, J., Pui, D. Y. H., Yook, S. J., and Kim, J. H. Nanoparticle contamination control for EUVL-technology: Especially for photomasks in carriers and scanners,

International Proceedings of SPIE, 7364:73640N
2009
18 Yook, S. J., and Ahn, K. H. Gaussian diffusion sphere model to predict mass transfer due to diffusional particle deposition on a flat surface in laminar flow regime,

Applied Physics Letters, 94:191909.
2009
17 Kim, J. S., Lee, K. S., and Yook, S. J. Frost behavior on a fin considering the heat conduction of heat exchanger fins,

International Journal of Heat and Mass Transfer ,
52:2581-2588.
2009
16 Yook, S. J., Fissan, H., Engelke, T., Asbach, C.,
van der Zwaag, T., Kim, J. H., Wang, J.,and
Pui, D. Y. H.
Classification of highly monodisperse nanoparticles of NIST-traceable sizes by TDMA and control of deposition spot size on a surface by electrophoresis,

Journal of Aerosol Science, 39:537-548.
2008
15 Yook, S. J., Fissan, H., Engelke, T., Asbach, C., van derZwaag, T., Kim, J. H., Eschbach, F., Wang, J., and Pui, D. Y. H. Controlled deposition of SiO2 nanoparticles of NIST-traceable particle sizes for mask surface inspection system characterization,

IEEE Transactions on Semiconductor Manufacturing, 21:238-243.
2008
14 Wang, J., Pui, D. Y. H., Qi, C., Yook, S. J., Fissan, H., Ultanir, E., and Liang, T. Controlled deposition of NIST-traceable nanoparticles as additional size standards for photomask applications,

Proceedings of SPIE, 6922:69220G.
2008
13 Yook, S.J., Fissan, H., Asbach, C., Kim, J. H., Dutcher, D.D.,
Yan, P. Y., and Pui, D. Y. H.
Experimental investigations on particle contamination of masks without protective pellicles during vibration or shipping of mask carriers,

IEEE Transactions on Semiconductor Manufacturing, 20:578-584.
2007
12 Yook, S. J.,Fissan, H., Asbach, C., Kim, J. H., van der Zwaag, T., Engelke, T., Yan, P. Y., and Pui, D. Y. H. Experimental investigations of protection schemes for extreme ultraviolet lithography masks in carrier systems against horizontal aerosol flow,

IEEE Transactions on Semiconductor Manufacturing, 20:176-186.
2007
11 Engelke, T., van der Zwaag, T., Asbach, C., Fissan, H.,
Kim, J. H.,Yook, S. J., and Pui, D. Y. H.
Numerical evaluation of protection schemes for EUVL masks in carrier systems against horizontal aerosol flow,

Journal of The Electrochemical Society, 154:H170-H176.
2007
10 Yook, S. J., Fissan, H., Asbach, C., Kim, J. H., Wang, J., Yan, P. Y., and Pui, D. Y. H. Evaluation of protection schemes for extreme ultraviolet lithography (EUVL) masks against top-down aerosol flow,

Journal of Aerosol Science, 38:211-227.
2007
9 Asbach,C., Fissan, H., Kim, J. H., Yook, S. J., and Pui, D. Y. H. Simple theoretic approach to estimate the effect of gravity and thermophoresis on the diffusional nanoparticle contamination under low pressure conditions,

Journal of Vacuum Science & Technology B 25:47-53.
2007
8 Asbach, C., Fissan, H., Kim, J. H., Yook, S. J., and Pui, D. Y. H. Technical Note: Concepts for protection of EUVL masks from particle contamination,

Journal of Nanoparticle Research, 8:705-708.
2006
7 Kim, J. H., Fissan, H., Asbach, C., Yook, S. J., Wang, J.,
Pui, D. Y. H., and Orvek, K. J.
Effect of reverse flow by differential pressure on the protection of critical surfaces against particle contamination,

Journal of Vacuum Science & Technology B, 24:1844-1849.
2006
6 Kim, J. H., Fissan, H., Asbach, C., Yook, S. J., Pui, D. Y. H., and Orvek, K. Investigation of thermophoretic protection with speed-controlled particles at 100, 50, and 25 mTorr,

Journal of Vacuum Science & Technology B, 24:1178-1184.
2006
5 Yook, S. J and Pui, D. Y. H. Experimental study of nanoparticle penetration efficiency through coils of circular crosssections,

Aerosol Science and Technology, 40:456-462.
2006
4 Kim, J. H., Fissan, H., Asbach, C., Yook, S. J., and Pui, D. Y. H. Speed-controlled particle injection into a low-pressure system,

Journal of Vacuum Science & Technology A, 24:229-234.
2006
3 Asbach, C., Kim, J. H., Yook, S. J.,
Pui, D. Y. H., and Fissan, H.
Analytical modeling of particle stopping distance at low pressure to evaluate protection schemes for extreme ultraviolet lithography masks,

Applied Physics Letters, 87:234111.
2005
2 Asbach, C., Pui, D. Y. H., Kim, J. H.,
Yook, S.J., and Fissan, H.
Modeling of protection schemes for critical surfaces under low pressure conditions: Comparison between analytical and numerical approach,

Journal of Vacuum Science & Technology B, 23:2419-2426.
2005
1 Kim, J. H., Asbach, C., Yook, S. J., Fissan H., Orvek, K., Ramamoorthy, A.,Yan, P. Y., and Pui, D. Y. H. Protection schemes for critical surface in vacuum environments,

Journal of Vacuum Science & Technology A, 23:1319-1324.
2005